CATV & MATV SYSTEM


FALCOM TECHNOLOGY SUPPLIES PRODUCT CATV & MATV FOR ANALOG AND DIGITAL SYSTEM


Analog Equipment


E-990 highly-responsive modulator designed for medium scale catv system with output frequency range from 47Mhz – 862 Mhz. It uses the crystal components (GaAs) components for the PLL circuits, SAW filter, amplifier and C panel (PhillipsTM), including CPU controlled VSB (Vestigial Side Band) modulator E 990C for a stable quality both in audio and video carrier.
Features
  • Double digital PLL, controlled by CPU
  • Adjustable RF output, it can be arranged within the frequency of 47 Mhz – 8620 Mhz
  • PAL B/G standard channel
  • Image input ranges from  0.5 VP-P to 1.5 VP-P
  • Sound system classification 4.5/5.5/6.0/6.5
  • Channel fine tuning accuracy up to 0.25 MHZ
  • Automatic saving before power turned off



FALCOM MW 963 modulator is a fixed channel modulator using three SAW filters circuits thus it can respond to the VSB (Vestigial Side Band) frequencies. This device has a high level stability and optimization. Video and audio frequencies circuits are built integrated in the PLL control circuit, thus it can provide high accuracy. The device also has video and audio modulated RF carrier signal in the frequencies range of 45 – 860 MHz. The Falcom MW963 modulator can receive audio video signal source from satellite receivers, video tape recorders, digital DVD/VCD players, and other similar equipment which has audio video composite output. That makes FALCOM modulator 963 MW has the optimum standards and features for MATV / CATV  system.

Features
  • Double digital PLL, controlled by CPU
  • Adjustable RF output, it can be arranged within the frequency of 47 Mhz – 8620 Mhz
  • PAL B/G standard channel
  • Image input ranges from  0.5 VP-P to 1.5 VP-P
  • Sound system classification 4.5/5.5/6.0/6.5
  • Channel fine tuning accuracy up to 0.25 MHZ
  • Automatic saving before power turned off


Output terminals which combines output signal from multiple modulators and other similar equipment into one stable RF output signal.  It is available in 3 series,  i.e. :  FC 12, FC 16  and  FC 24.
Features
  • High insulating capability
  • Low insertion loss (depends on the type)
  • Sufficient stability for mixing signals
  • Suitable for lower and middle class networks
  • Test port level : -10dB




Receiver MPEG 4 Full HD 1080
Scrambler Analog 


HFC AMPLIFIER 




Features
  • Using  1 amplifier module (PhillipsTM) with an optimum nominal gain of 34 dB
  • Fitted with 2 front reinforcement amplifier transistors that makes higher signal amplification with the signal parameter index (C/N, CTB, CSO)
  • Using 550 MHz PAD and an adjustable attenuator  within the equalizer, makes it easier to set a certain signal slope level
  • Changeable output configuration  (splitted into 2-way output or tapped)
  • Casing design is sturdy, light weight, and rust-proof
  • Ideal usage as a main line amplifier for keeping the index parameters, image quality and signal slope suffice a required level for a wider networks point distribution



Features
  • Using 1 amplifier module with a nominal gain of 30 dB
  • Using 550 MHz PAD and an adjustable attenuator  within the equalizer, makes it easier to set a certain signal slope level
  • Changeable output configuration  (splitted into 2-way output or tapped)
  • Casing design is sturdy, light weight, and rust-proof







Features
  • Using 2 power doubler amplifier module (PhillipsTM) with an optimum gain of 35 dB.
  • Using Manual Gain Control (MGC)
  • Using 550 MHz PAD and an adjustable attenuator within equalizer, makes it easier to set a certain signal slope level
  • Changeable output configuration (splitted into 2-way output or tapped)
  • Chassis design is sturdy, lightweight, and rustproof
  • Ideal to use as a main line amplifier to keep the index parameters, image quality and signal slope suffice a required level for a wider networks point distribution
  • Automatic voltage switching




Features
  • Using 1 power doubler amplifier module (PhillipsTM) with optimum nominal gain of 34 dB
  • Fitted with 2 front reinforcement amplifier transistors that makes higher signal amplification with the stable parameter index (C/N, CTB, CSO)
  • Using double equalizer for controlling the slope of signal level
  • Can be used as two-way amplifier for data transmission / internet.
  • Changeable output configuration  (splitted into 2-way output or tapped)
  • Casing design is sturdy, light weight, and rust-proof
  • Ideal usage as a main line amplifier for keeping the index parameters, image quality and signal slope suffice a required level for a wider networks point distribution
  • Automatic voltage switching



 FTA D700C is the outdoor series with a two-way trunk amplifier comes with high stability and low distortion advantages. Compatible with the output terminals and main CATV network.
Features
  • High quality aluminium casing, resistant to water and dust (Ingress Protection 56) and has an advantages of good throw-out heat
  • Easy installation and adjustment
  • Using NEC  double  power amplifiers
  • An AGC (Automatic Gain Control) series are available, which ensure signal stability



 



HFC OPTICAL



Features :
  • Vertical type, small size
  • 3 pcs inlet/outlet
  • 48 ~ 96 cores total capacity
  • Slide-in-lock design, over 90° opening angle tray.
  • Elastic integrated seal fitting
  • Earthing deriving device can be installed on the house of FOSC
  • Operating temperature -40°C~+65°C
  • The capacity of bunchy FOST 022 is from 6 to 16 cores
  • The capacity of bunchy FOST 023 is from 12 to 24 cores quantity of bunchy FOST and heat shrinkable protective sleeves are to be determined according to the total capacity of FOSC. ( Note : each bunchy fiber has one core after splicing, which needs one piece of bunchy heat shrinkable protective sleeves
Technical Specifications :
Outside Dimension ( L x W x H ): 280x200x90 (mm)
Weight (Excluding Outside Box): 1200-1500 (gr)
Number of Inlet /Outlet Ports: Max. 4 pcs
Diameter of Fiber Cable: 8-24 (mm)
Capacity of FOSC: Bunchy 6-96 (cores)




Features
  • 19″ standard installation, adjustable in forward and backward directions
  • Suitable for being installed in different kinds of racks or cabinets
  • FC and SC adapter panels available
  • 3 input cores and 15 output cores
  • Height :1U
Technical Specifications
Use: Indoor, 19″ rack mounted
Maximum Capacity: 3 input cores and 15 output cores
External Dimensions: 485mm*305mm*47mm
Weight: 1.7kg
Material: Steel plate with electro static spray painting




Standard adaptor is used to connect two and of optical fiber with the same connectors, for example, FC,SC,ST and so on. Single core, double cores (SC) are optional upon request.
Features :
  • FTTH, LAN, PON & Optical CATV
  • Local ring net
  • Optical fiber communication system
  • Optical fiber test equipment
  • Optical fiber sensor
  • Accurate imension
  • Good exchangeability
  • Good repeatability
  • Good wear resistance


Features :
  • Up-down bisection, horizontal type 6 pcs inlet/outlet 48~96 cores total capacity
  • Slide-in-lock design, over 90° opening angle tray
  • Elastic integrated seal ensure tightening fit
  • Housing provide fire resistant, waterproof, and quake proof for splicing while handling
  • Operating temperature -40°C~+65°C
  • The capacity of bunchy FOST 016 is from 6 to 16 cores
  • The capacity of bunchy FOST 024 is from 12 to 24 cores quantity of bunchy FOST and heat shrinkable protective sleeves are to be determined according to the total capacity of FOSC (Note : each bunchy fiber has one core after splicing, which needs one piece of bunchy heat shrinkable protective sleeves )
  • Ribbon FOST 017 can accommodate 3 pieces of ribbon heat shrinkable protective sleeve
Technical Specifications :
Outside Dimension ( L x W x H ):  410 x 200 x 120 (mm)
Weight (excluding outside box):  1985 – 2300 (gr)
Number of Inlet/Outlet Ports:  3 pcs on each side (total 6 pcs)
Diameter of Fiber Cable:  8-16 (mm)
Capacity of FOSC:  Bunchy 6-144 (cores)
Ribbon Max.:  216 (cores)



Features :
Application: Aerial, underground, pipeline, hand-hole
The Ambient Temperature Ranges: 40°C to 60°C
Outside Dimension (height x diameter): 390mm x 190mm
Number of Inlet/Outlet Ports:  4 pieces
Diameter of Fiber Cable:  8mm – 16mm
Capacity:  Bunchy 6-96 cores
Fiber Optic Splice Tray:  Min. 2 trays – max. 5 trays



NODE 900M is using 2 way forward (47 MHz-750MHz) and reverse (5 MHz-35 MHZ) with  changeable  frequency  bandwidth.
Features :
  • Aluminium casted housing, easily remove the heat
  • Using plug-ins for easier adjustment
  • Frequency division is changeable due to the use of filter
  • Easy maintenance
  • Easy operation
  • High stability
  • Two types are available : 4W and 2W


Highly responsive PIN photoelectric conversion tube. Optimized circuit design, optimizing the whole signal path, made the photo electronic signal transmission sufficient. Reliable RF attenuation chips, good RF attenuation and balanced linear, high precision of signal slope level. A GaAs amplifier modul, double power output advantages, high gain and low distortion. Excellent AGC characteristics, when the input of optical power reaches -7 – 3dBm, the output level, CTB and CSO basically unchange











HFC ACCESORIES